Manufacturer for Wi-Fi 11ac - Fiber Node Transponder, SA120IE – MoreLink
Short Description:
Product Detail
Product Tags
Related Video
Feedback (2)
Manufacturer for Wi-Fi 11ac - Fiber Node Transponder, SA120IE – MoreLink Detail:
Cable Modem Features
▶DOCSIS/EURODOCSIS 1.1/2.0/3.0, Channel bonding: 8*4
▶Two MCX (Female) connectors for Downstream and Upstream
▶Provide two-Port Giga Ethernet MDI Signals to target board (Digital Board) through J1 & J2
▶Get DC Power Supply from Target Board by use of J2
▶Standalone External Watchdog
▶Temperature sensor on board
▶Small size (dimensions): 113mm x 56mm
▶Accurate RF power level 2dB at all temperature range
▶FBC for Spectrum Analyzer, integrated Splendidtel Spectrum Analyzer (SSA)
▶Support Low Power Mode and Full Function Mode Switchable
SW Features
▶DOCSIS®/Euro-DOCSIS® HFC environment auto detection
▶UART/I2C/SPI/GPIO driver customization for various devices monitoring. Such as Fiber node, Power Supply, RF Amplifier
▶Docsis MIBs / Any other customized MIB support
▶Open system API and data structure for 3rd party application’s access
▶Low power signal detection. Signal lower than -40dBmV will be represented with built-in Spectrum Analyzer
▶CM MIB Files are open for customers
▶CM management Web GUI is available on WAN or LAN
▶MSO can reboot the CM remotely via Telnet or SNMP
▶Switchable between Bridge and Router mode
▶Supports DOCSIS device upgrade MIB
System Block
External Watchdog
An external watchdog is used to make sure the system’s operation reliably. Watchdog is kicked by the
Firmware every once in a while, so that the CM does not reset. If there’s something wrong with the CM
Firmware, then after a certain period (watchdog time), the CM will reset automatically.
Technical Parameters
Protocol Support | ||
u DOCSIS/EuroDOCSIS 1.1/2.0/3.0u SNMP v1/v2/v3
u TR069 |
||
CPU and Memory | ||
CPU | BCM33838M (8×4, Commercial, 0 ~ +70 oC)BCM3383DI (8×4, Industrial, -40 ~ +85 oC) | |
Memory | 64MB DDR3 | |
Flash | 8MB SPI Flash | |
Connectivity | ||
RF: MCX1, MCX2 | Two MCX Female, 75 OHM, Straight Angle, DIP | |
Ethernet Signal/PWR: J1, J2 | 1.27mm 2×17 PCB Stack, Straight Angle, SMD2xGiga Ethernet Ports | |
RF Downstream | ||
Frequency (edge-to-edge) | u 88~1002 MHz (DOCSIS)u 108~1002 MHz (EuroDOCSIS) | |
Channel Bandwidth | u 6 MHz (DOCSIS)u 8 MHz (EuroDOCSIS)
u 6/8 MHz (Auto Detection, Hybrid Mode) |
|
Modulation | 64QAM, 256QAM | |
Data Rate | Up to 400 Mbps by 8 Channel bonding | |
Signal Level | Docsis: -15 to +15 dBmVEuro Docsis: -17 to +13 dBmV (64QAM); -13 to +17 dBmV (256QAM) | |
RF Upstream | ||
Frequency Range | u 5~42 MHz (DOCSIS)u 5~65 MHz (EuroDOCSIS)
u 5~85 MHz (Optional) |
|
Modulation | TDMA: QPSK,8QAM,16QAM,32QAM,64QAMS-CDMA: QPSK,8QAM,16QAM,32QAM,64QAM,128QAM | |
Data Rate | Up to 108 Mbps by 4 Channel Bonding | |
RF Output Level | TDMA (32/64 QAM): +17 ~ +57 dBmVTDMA (8/16 QAM): +17 ~ +58 dBmV
TDMA (QPSK): +17 ~ +61 dBmV S-CDMA: +17 ~ +56 dBmV |
|
Networking | ||
Network protocol | IP/TCP/UDP/ARP/ICMP/DHCP/TFTP/SNMP/HTTP/TR069/VPN (L2 and L3) | |
Routing | DNS / DHCP server / RIP I and II | |
Internet Sharing | NAT / NAPT / DHCP server / DNS | |
SNMP version | SNMP v1/v2/v3 | |
DHCP server | Built-in DHCP server to distribute IP address to CPE by CM’s Ethernet port | |
DCHP client | CM automatically gets IP and DNS server address from MSO DHCP server | |
Mechanical | ||
Dimensions | 56mm (W) x 113mm (L) | |
Environmental | ||
Power Input | Support wide power input: +12V to +24V DC | |
Power Consumption | 12W (Max.)7W (TPY.) | |
Operating Temperature | Commercial: 0 ~ +70 oCIndustrial: -40 ~ +85 oC | |
Operating Humidity | 10~90% (Non Condensing) | |
Storage Temperature | -40 ~ +85 oC |
Board-to-Board Connectors between Digital and CM Board
There’re two boards: Digital board and CM Board, which use four pairs of board-to-board connectors to transmit RF signals, Digital signals and power.
Two pairs of MCX connectors used for DOCSIS Downstream and Upstream RF Signals. Two pairs of Pin Header/PCB Socket used for Digital Signals and Power. CM board is placed under the Digital Board. CM’s CPU is contacted to the housing through thermal pad to transfer the heat away from CPU and towards the housing and environment.
The mated height between two boards is 11.4+/-0.1mm.
Here’s the illustration of matched board-to-board connection:
Note:
Cause of Board-to-Board design for two PCBA Boards, in order to make sure stable and reliable connection, therefore, when
To design the Housing, it should be taken the assembly engineering and screws for fix into consideration.
MCX1, MCX2: 75 OHM, Female, Straight Angle, DIP
MCX1: DS
MCX2: US
Matched MCX Male: 75 OHM, Male, Straight Angle, DIP
J1, J2: 2.0mm 2×7 PCB Socket, Straight Angle, SMD
J1: Pin Definition (Preliminary)
J1 Pin |
CM Board |
Digital Board |
Comments |
1 |
GND |
||
2 |
GND |
||
3 |
TR1+ |
|
Giga Ethernet Signals from CM board. There’s NO Ethernet transformer on the CM board, here’re Only the Ethernet MDI Signals to Digital Board. RJ45 and Ethernet transformer are placed at Digital Board. |
4 |
TR1- |
|
|
5 |
TR2+ |
|
|
6 |
TR2- |
|
|
7 |
TR3+ |
|
|
8 |
TR3- |
|
|
9 |
TR4+ |
|
|
10 |
TR4- |
|
|
11 |
GND |
|
|
12 |
GND |
|
|
13 |
GND |
|
Digital board provides Power to CM board, the power level range is; +12 to +24V DC |
14 |
GND |
|
J2: Pin Definition (Preliminary)
J2 Pin |
CM Board |
Digital Board |
Comments |
1 |
GND |
||
2 |
Reset |
Digital board can send a reset signal to CM board, then to reset the CM. 0 ~ 3.3VDC | |
3 |
GPIO_01 |
0 ~ 3.3VDC | |
4 |
GPIO_02 |
0 ~ 3.3VDC | |
5 |
UART Enable |
0 ~ 3.3VDC | |
6 |
UART Transmit |
0 ~ 3.3VDC | |
7 |
UART Receive |
0 ~ 3.3VDC | |
8 |
GND |
||
9 |
GND |
0 ~ 3.3VDC | |
10 |
SPI MOSI |
0 ~ 3.3VDC | |
11 |
SPI CLOCK |
0 ~ 3.3VDC | |
12 |
SPI MISO |
0 ~ 3.3VDC | |
13 |
SPI Chip Select 1 |
0 ~ 3.3VDC | |
14 |
GND |
PCB Dimension
Product detail pictures:
Related Product Guide:
It adheres on the tenet "Honest, industrious, enterprising, innovative" to develop new items frequently. It regards buyers, success as its very own success. Let us produce prosperous future hand in hand for Manufacturer for Wi-Fi 11ac - Fiber Node Transponder, SA120IE – MoreLink, The product will supply to all over the world, such as: Croatia, Philippines, Serbia, We provide OEM services and replacement parts to meet the varying needs of our customers. We give competitive price for quality solutions and we are going to make certain your shipment is handled quickly by our logistics department. We sincerely hope to have the opportunity to meet with you and see how we can help you further your own business.
By Annie from Colombia - 2017.08.18 18:38
This company has the idea of "better quality, lower processing costs, prices are more reasonable", so they have competitive product quality and price, that's the main reason we chose to cooperate.
By Lynn from belarus - 2017.09.29 11:19